How To Specify Vci Odis

This instruction will guide you on the way to change gearbox computer part number via ODIS-Engineering on AUDI A7DSG.

Mar 03, 2021 #21071 ODIS-Service 5.2.4: During the diagnosis, the connection to the VCI was lost and could not be re-established #21072 After an update (to ODIS 5.2.4) the diagnostic interface is no longer recognized via WLAN or cable. With the information on the radio to remove CP, to code it for another VIN. Is an anti-theft measure. ODIS will connect to VW and FAZIT database to check if the unit is stolen. It’ll then check SVM to see if it’s up to date and remove component protection. Here is a link describing GEKO which is the system which policies the component. Oct 30, 2017 I reconized that only a VCI 6154 is available in the Settings of both Programms. I have only a 5054 as VCI. How to Change the Interface from 6154 to 5054? Both Programms on Windows 10 Pro x64 Thanks in advance hi mate where i can get this version and post set up is full?? ODIS-S 4.2.3 and Odis-E 7.2.2 VCI Settings.

Preparation:

Note:

For engine computer number changing

Computer’s number of different displacement engines cannot be changed

Different hardware numbers cannot be changed

Specify

The computers of different power engines anti-theft will be locked, and need to be unlocked online

After number is successfully changed, there may be a fault code that cannot be cleared

Before changing the number, please refer to the ETKA Volkswagen Audi electronic parts catalog for applicable vehicles.

For gearbox computer number changing

Part of the gearbox computer number changed requires the release of the anti-start lock first

DQ200.DQ250.0AM gearbox computer is not suitable for this method

After number is changed, the computer matching value is lost and needs to be re-learned

Procedures:

Check computer part number: Enter the ODIS self-diagnosis

Or check the part label directly

The original part number is 4G1927156A on AUDI A7DSG. We need to search flash file same as the original car in the data to change the number.

The replacement part number 8R0927156Q belong to AUDI Q5 must change to 4G1927156A, otherwise it will appear ODS05104 error message when we select FL_4G1927156A_0003.frf as the following.

Enter the “Function Configuration”–>”Flash(engineering) “ remove the tick and save

Click “Flashing Start”, it takes about 2-10 minutes to finish number changed.

After number changed, release anti-start lock and re-learn computer matching value by ODIS.


Readers who read this article also read:

Original Fcar FVCI Passthru J2534 VCI Diagnosis, Reflash and Programming Tool works same function as Autel MaxiSys Pro MS908P. It supports J2534 protocol, and it will support other protocol for free later. In addition, the FVCI J2534 VCI supports multiply communication manner of DOIP protocol, and it can set up Ethernet(tx_+, tx_-, rx_+, rx_-) and active line to any pin number of OBD2 except for ground pins and power pin.
Fcar FVCI Passthru specification:
Hardware function
J2534ISO15765
ISO14230
ISO9141
ISO14230
J1850
SCI
Single wire CAN
DOIPEthernet port convert to OBD2
Local area network of FVCI convert to OBD2
Program voltage port5v-20v
Ethernet port1. Ethernet port to ODB2 interface for DOIP
2. Ethernet port to local area network of FVCI
Analog input15 pins analog input
Vehicle port26 pins port communicate to vehicle
Update pinUse for update firmware of FVCI
DC12v power supply
Diagnose function
TOYOTA Techstream
HONDA HDS
Volkswagen ODIS
VOVOL VIDA
GM GDS
BMW ISTA
JARGUR LANDROVER JLR SDD
Acura, Honda
Audi
BMW
Chrysler, Dodge, Jeep, Eagle, Plymouth
Ford, Lincoln, Mercury
GM
Hyundai
Infiniti
Isuzu
Jaguar
Kia
Land Rover
Lexus
Mazda
Mercedes-Benz
Mini
Mitsubishi
Nissan
Porsche
Subaru
Suzuki
Toyota, Scion
Volkswagen
Volvo

How to install/set up Fcar FVCI J2534 software?

OEM official website : http://www.fcar.com
1. Software setup
The FVCI tool package is in the CD, or it can download from http://www.fcar.com.
2) Click “Next” button.

How To Specify Vci Odis File

3) Go on click “Next” button
4)Click “finish” button. The software setup done.
2. Install .net framework4.0
How To Specify Vci Odis
1) FVCI connect to power, then the device working.
3) Click “Start”
4) Click “control panel”.
5) Change the view to small icon in the top right corner.
Odis
6) Find “Device manager”.
7) And you will find “FVCI” label. (The USB must be connected to the computer.)
8) Right click ”FVCI”, and click “Update Driver Software”.
How To Specify Vci Odis
9)Click “Browse my computer for driver ”.
10）Click “Browse”, and input the driver path of USB driver package.
12) If there is a windows security popup, Click “Install this driver software anyway”.
13)　If following information displays, it means install successful.
14) Check the “device manager”, if you see below figure, it means FVCI has been connected to the computer.
15) Start running software.
How to specify vci odis settings

How To Specify Vci Odis In Excel

How to Update Fcar FVCI J2534 Passthru Software & Firmware?

1. Click “FVCI” icon on the desktop. Note: The computer must be connected to internet.
2. Click “Read Version” can read FVCI software and hardware version.
3. Click “Firmware Update” can update the hardware.
4. Click “Software Update” can update the software.
5. Click”DOIP”, then click “Enter DOIP mode”, the FVCI will enter the situation of Ethernet convert to OBD2 of DOIP.
6. Click ”Firmware Refresh” when you operate“firmware update” error.

How To Specify Vci Odis Download

Update Tips
1) Please enable internet connection before upgrade
2) The firmware version and software version must be the newest version mean while. Other wise the device will appear some error.
3) If you use “Firmware update” failed, you can use “Firmware refresh”.